Sort 1   Sort 2    
  • Product

    Carbon Steel Pipes - Round - Seamless Pipe - API Pipe, Tensile 235-3000MPa, ∅6-170mm, Thickness 0.8-30mm, AISI 304/ST37-2, ASME... - FOB China

  • Requirement:
  • Short Description: Jiangsu Tiancheng Steel Pipe Co., Ltd. is a big professional manufacturer and exporter of steel tubes and pipes in China. We can makes and markets cold-drawn, cold-rolled and hot-rolled seamless steel pipes and cold-drawn special-section seamless pipes which are widely applied in the industries of petrochemical, boiler, automobile, mechanical, construction.....
  • Detailed Description:

    Jiangsu Tiancheng Steel Pipe Co., Ltd. is a big professional manufacturer and exporter of steel tubes and pipes in China. It was established in 1989, with a registered capital of six hundred forty-one million US Dollars. Owning more than 1500 professional employees, including over 150 engineers and technicians. We can makes and markets cold-drawn, cold-rolled and hot-rolled seamless steel pipes and cold-drawn special-section seamless pipes which are widely applied in the industries of petrochemical, boiler, automobile, mechanical, construction..... Our factory through ISO9001:2000 certificate, has aggressive leadships and outstanding professionals. We can supply the Size: (Φ6 - Φ680) x (0.5 - 87) mm, but we can also produce other specification according to the customers’requirements.
     

  • Detail of Company who is publishing this product information

    No Company Name Country State/Region Company Picture Current Stock Lists Company Introduction
    1 Jiangsu Tiancheng Steel Pipe Co. Ltd
    Jiangsu Tiancheng Steel Pipe Co. Ltd
    China.htmlChina Jiangsu Jiangsu Tiancheng Steel Pipe Co. Ltd - Company… Jiangsu Tiancheng Steel Pipe Co., Ltd. was established in 1989, with a registered capital of six hundred forty-one million US Dollars. Owning more than 1500 professional employees, including over 150 engineers and technicians. We can makes and markets cold-drawn, cold-rolled and hot-rolled seamless steel pipes and cold-drawn special-section seamless pipes which are widely applied in the industries of petrochemical, boiler, automobile, mechanical, construction.....
    Type of Business:

    Product List:

    Company Certification:

    Company Registration Number:
    320483000078398

    Company Certificate:
    Jiangsu Tiancheng Steel Pipe Co. Ltd - Company…

    Number of Employees in the Company:

    Annual Sales Value:

    Phone:
    +8613337883086

    Company Email:

    Company Web Site:

    Total: 1 record     Go Companies »
  • User who is publishing this product information

    No User Full Name Company Verified Manufacturer Position Phone Email Country Registration Date on Steelads.com
    1 Mr. Josen Dong Jiangsu_Tiancheng_Steel_Pipe_Co_Ltd.htmlJiangsu Tiancheng Steel Pipe Co. Ltd Manager +86133337883086 - Login to Steelads - China.htmlChina 25 Aug 2010
    Publisher Location (according to IP address):

    Publisher City (according to IP address):
    Jiangsu, Changzhou

    Total: 1 record     Go List of Employees - Metal Companies »
      • Carbon Steel Pipes - Round - Seamless… Standards

        No Standard No Society Summary
        1 ASTM A106 ASTM ASTM A106 / A106M - Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service. This specification covers carbon steel pipe for high-temperature service. These pipes are suitable for welding, bending, flanging, and similar forming operations.
        Scope:

        Abstract

        This specification covers carbon steel pipe for high-temperature service. These pipes are suitable for welding, bending, flanging, and similar forming operations. Mechanical testing of the specimens shall include tensile, bending, flattening, hydrostatic and nondestructive electric tests. Specimens undergoing bending tests shall consist of sections cut from a pipe. For flattening tests, the specimens shall be smooth on the ends and burr-free, except when made on crop ends. All tests shall be performed in room temperature. If any test specimen shows flaws it can be discarded and substituted for another test specimen. Before testing, if a specimen has scribe scratches, a retest shall be allowed. A retest shall also be allowed if a specimen breaks in an inside or outside surface flaw.

        This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

        1. Scope

         

        1.1 This specification covers seamless carbon steel pipe for high-temperature service (Note 1) in NPS 1/8 to NPS 48 [DN 6 to DN 1200] (Note 2) inclusive, with nominal (average) wall thickness as given in ASME B 36.10M. It shall be permissible to furnish pipe having other dimensions provided such pipe complies with all other requirements of this specification. Pipe ordered under this specification shall be suitable for bending, flanging, and similar forming operations, and for welding. When the steel is to be welded, it is presupposed that a welding procedure suitable to the grade of steel and intended use or service will be utilized.

        Note 1-It is suggested, consideration be given to possible graphitization.

        Note 2-The dimensionless designator NPS (nominal pipe size) [DN (diameter nominal)] has been substituted in this standard for such traditional terms as "nominal diameter," "size," and "nominal size."


        1.2 Supplementary requirements of an optional nature are provided for seamless pipe intended for use in applications where a superior grade of pipe is required. These supplementary requirements call for additional tests to be made and when desired shall be so stated in the order.

        1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

        1.4 The following precautionary caveat pertains only to the test method portion, Sections 11, 12, and 13 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
         


        Webpage:

        2 ASME SA213 ASME Identical with ASTM Specification ASTM A213 -89a. This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes. Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. The tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.
        Scope:

        1. Scope

         1.1 This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2.

        1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements.

        1.3 The tubing sizes and thicknesses usually furnished to this specification are 1/8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification.

        1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.


        Webpage:

        3 ASME SA179 ASME Identical with ASTM Specification ASTM A179-88a. This specification covers minimum-wall thickness, seamless cold-drawn low-carbon steel tubes for tubular heat exchangers, condensers, and similar heat transfer apparatus. Tubes shall be made by the seamless process and shall be cold drawn. Heat and product analysis shall be performed wherein steel materials shall conform to required chemical compositions of carbon, manganese, phosphorus, and sulfur. The steel materials shall also undergo hardness test, flattening test, flaring test, flange test, and hydrostatic test.
        Scope:

        1. Scope

        1.1 This specification covers minimum-wall-thickness, seamless cold-drawn low-carbon steel tubes for tubular heat exchangers, condensers, and similar heat transfer apparatus.

        1.2 This specification covers tubes 1/8 to 3 in. [3.2 to 76.2 mm], inclusive, in outside diameter. Note 1Tubing smaller in outside diameter and having a thinner wall than indicated in this specification is available. Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] in outside diameter or with a wall thickness under 0.015 in. [0.4 mm].


        1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.


        Webpage:

        Total: 3 records     Go Standards »
      • Country Details

        No Country Name Capital Region Surface Area Population
        1 China Beijing Eastern Asia 9,572,900 km² 1,277,558,000 people
        Total: 1 record     Go Countries »




      About Us Companies Latest Products Browse Product Pictures Old Steelads Website TOP25 World Steel Companies

      Copyright © 2004-2015 B2B Metal & Steel Products Steelads.com, Gcoupon.com. All rights reserved.

      My IP Address powered by Myip.ms Facebook bot last visit time powered by Myip.ms
      World No.1 Global Classified Metal & Mineral Products Database